Free x dating - Slackware updating

is an automated tool for managing (installing, upgrading, and, uninstalling) of 64-bit part of alien BOB's multilib for slackware-64.The 64-bit part of the multilib is a subset of packages which allows to turn a pure 64-bit slackware-64 into a multilib slackware-64.it installs new boot-firmware/kernel/kernel-modules and says "Ok, just do it! Which isn't always the best thing to allow because you don't really know what's being installed, or upgraded, or overwritten, or deleted, on your Slackware ARM system.

slackware updating-48slackware updating-25

Slackware updating Cam2cam finder

linux kernel boot options reference unfortunately, the HDMI adds an additional audio device and put it in as default.

In the Gentoo Forum there is a nice description how to fix the order.

An alternative solution would be to manage/install any upgrades yourself.

If required, the SARPi kernel, kernel modules, and boot firmware packages (.txz) are available on the SARPi downloads page and are updated quite often.

When defined, it must refer to the multilib mirror that will be used by --install, --check-updates, --list-updates, and --upgrade when user does not provide one on the command line. These signatures are used in conjunction with MULTILIB64_PACKAGES to identify : This is optional.

When defined, this must be an array containing the basename of multilib packages to blacklist, which must not be installed.

*", ATTR=="ac::a", ATTR=="0x0", ATTR=="1", KERNEL=="eth*", NAME="wlan0" #!

/bin/sh set -o nounset TOUCHPADID=$(xinput list | grep -i Synaptics) for ELEMENT in $; do if [ "$" == "id=" ]; then TOUCHPADID=$( echo $ | awk | cut -d= -f2) fi done TOUCHPADSTATE=$(xinput list $ | grep "This device is" | awk ) if [ "$" == "This device is disabled" ]; then xinput set-prop $ "Device Enabled" 1 else if [ -z "$" ]; then xinput set-prop $ "Device Enabled" 0 else echo "unknown state # lvm version # pvs -o lv_name,lv_size,lv_attr # fdisk /dev/sda && fdisk /dev/sdb Device Boot Start End Blocks Id System /dev/sda1 * 2048 104447 51200 83 Linux 50M /dev/sda2 104448 366591 131072 8e Linux 128M /dev/sda3 366592 3907029167 1953331288 8e Linux Rest - # mkfs.ext4 /dev/sda1 && mkfs.ext4 /dev/sdb1 - # pvcreate /dev/sda2 /dev/sda3 /dev/sdb2 /dev/sdb3 # vgcreate -s 32M vg00 /dev/sda3 /dev/sda2 /dev/sdb3 /dev/sdb2 - # lvcreate -L 12G -n lvol0 vg00 /dev/sda3 # lvcreate -l 59098 -n lvol1 vg00 /dev/sda3 # lvcreate -l 128 -n lvol2 vg00 /dev/sda3 - # lvconvert -m 1 --mirrorlog mirrored /dev/vg00/lvol0 /dev/sdb3 /dev/sda2 /dev/sdb2 # lvconvert -m 1 --mirrorlog mirrored /dev/vg00/lvol1 /dev/sdb3 /dev/sda2 /dev/sdb2 # lvconvert -m 1 --mirrorlog mirrored /dev/vg00/lvol2 /dev/sdb3 /dev/sda2 /dev/sdb2 # dmsetup status - # mkfs.ext4 /dev/vg00/lvol0 # mkfs.ext4 -i 65536 /dev/vg00/lvol1 # mkswap /dev/vg00/lvol2 Findings - the 96MByte partition does not fit 3x 32MByte PE. Slackware needs some manual work as there is no default initrd for the LVM scan and activation during boot. TXT from Eric Hameleers # mount -o bind /proc /mnt/proc # mount -o bind /sys /mnt/sys # mount -o bind /dev /mnt/dev # chroot /mnt # mkinitrd -c -k $(uname -r) -m ext4 -f ext4 -r /dev/vg00/lvol0 -L # mkinitrd -c -k 2.6.38 -r /dev/vg00/lvol0 -L # lspci .0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) .0 0280: 14e53 (rev 01) # lshw *-network UNCLAIMED description: Network controller product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: [email protected] version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d2000000-d2003fff # modprobe -r b44 b43 b43legacy ssb the ssb module can not be removed because it is used by USB modules the Broadcom source is - as all closed source development - not up to date and needs a change in the include file src/linux/linuxver.h # PCI device 0x11ab:ox436c (sk2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?

For that, users may use its little brother, compat32pkg. This is required and must refer to the directory used to store packages downloaded from multilib mirrors and from slackware-64 mirrors.

By default, MULTILIBPKG_CACHE is set to /var/cache/multilibpkg.

Also uses the Slackware Linux instructions for installation, upgrading or removing packages.

Tags: , ,